ROOTVG - AIX & POWER Portal

Integrated Virtual Ethernet Adapter Management

Home

Help

Login

Register

	Welcome, Guest. Please login or register.	December 05, 2008, 12:28:26 PM
		Login with username, password and session length

ROOTVG > AIX > AIX6 Implementation and Administration > Integrated Virtual Ethernet Adapter Management

Pages: [1] Go Down

« previous next »

Print

	Author	Topic: Integrated Virtual Ethernet Adapter Management (Read 924 times)
0 Members and 1 Guest are viewing this topic.

Michael

Administrator
Hero Member

Posts: 530

Re: Integrated Virtual Ethernet Adapter Management

« Reply #1 on: August 15, 2008, 02:57:18 PM »

P6 boxes are still a bit new to all of us, and unfortunately, I dont always have access to one, so I cannot check all of this.

As you have allocated all resources to a single partition (a 'classic' SMP server as it were) I would ignore all the references to lhea - logical host ethernet adapter. In all honesty though, I do not know how the system will react to lhea when all resources are assigned.

Further - have you done an install, or is this a clone/preinstalled image? It may be that there are many interfaces that are defined, but not available (although as I type this I recall that entstat -d only works with Available interfaces).

I'll do some tests on p5 boxes with AIX 5.3 and AIX 6.1 - although the AIX 6.1 systems will not have any physical resources (VIOS is still AIX 5.3 atm) - and see if I can find similar differences.

And I'll repeat these when I get access to a p6 system again.

p.s. when I read Integrated Virtual Ethernet - I thought "Virtual Ethernet", and realize that this is about what the 'techies' refer to as HEA and lhea - Host Ethernet Adapter and Logical Host Ethernet Adapter.

please include some information about what settings you used to setup and define the HEA and LHEA for the managed system, and the partition - respectively.


« Last Edit: August 15, 2008, 03:00:17 PM by Michael »	Logged

dvsweden

Registered

Posts: 1

Integrated Virtual Ethernet Adapter Management

« on: July 31, 2008, 03:46:11 PM »

I am getting unexpected results from entstat occur new p6 6.1 boxes and seems to be reproducible on all of my p6 AIX 6.1 boxes.

Here is an example of what I expected to see from a p5 AIX 5.3 box:
[ts-p520al]: entstat -d ent2 | grep -i link
Link Status: Up
Link Status: Up

same command on the p6 aix6 box
[webdb-test]: entstat -d ent0 | grep -i link
Physical Port Link State: Down

slightly results looking for port
[webdb-test]: entstat -d ent0 | grep -i port

Physical Port Link State: Down
External-Network Switch-Port Operational State: 10000 Mbps / 10
Gbps, Full Duplex
Port Operational State: Permit all VLAN tagged frames

Confusing because:
1.) physical link is clearly up. I can ping inside and outside my subnet no prob
lem
2) Speed has been set so I am not sure where the 10G is coming from
:
[webdb-test]: lsattr -El ent0
media_speed 1000_Full_Duplex Requested media speed
True

I need to understand what is going on with networking on new p6
AIX6.1 environments.

In the Integrated Virtual Ethernet Adapter REDP-4340-00 red book
p57 example 4-13 clearly shows that you should be able to do:

enstat -d entN | grep Port and get similar to expected results:

When I run that exact command I get:

[webdb-test]: entstat -d ent0 | grep Port
Logical Host Ethernet Port (l-port) Driver Properties:
/ 0Logical Port Number: 0
Logical Port Number: 0
Logical Port Number: 0
Logical Port Number: 0
Logical Port Number: 0
Logical Host Ethernet Port (l-port) Driver Properties:
Physical Port Link State: Down
Port Receive Control: Down
Logical Host Ethernet Port (l-port) Specific Properties:
Logical Port Number: 3
External-Network-Switch (ENS) Port Speed: Down
External-Network Switch-Port Operational State: 10000 Mbps / 10
Gbps, Full Duplex
Logical Port Valid: VLAN Extract: False
Port Operational State: Permit all VLAN tagged frames
Number of Default QPNs for Port: -246962616
Port Receive Control Mask: 0x400000000
Port Query Mask: 0x2506F7274
Port Modify Mask: 0xE800000000000000
[webdb-test]:

note:Physical Port Link State: Down

Any ideas on how to determine that networking is properly set up under AIX 6.1?

I suspect that all of the above has to do with how I created and allocated the lpars (dedicated all resources assigned to one lpar) - but I've gone through and redone the profile several times and I get the same results.